Surround sound hook up, on this page

How to Connect Surround Sound to a Computer

October 2019

To accomplish this, you'll need to strip some of the wire away with wire cutters and then clip them into place on the back of the speaker. Your surround speakers should be placed about two feet above ear level and angled down slightly so that they point at the audience. Your two surround speakers should be placed on either side of the viewing area, pointed directly at the audience. Question Audio from streaming on Ruko tv to Surround sound not working. New posts Trending Search forums.

  1. The plug will look like the plug on the end of any pair of headphones.
  2. Tips You may have to tweak individual item settings before your surround sound system setup is complete.
  3. Do not connect the front speakers to one another via speaker wire.
  4. While you can follow general instructions to get decent sound out of your speakers, the best way to optimize them for perfect sound is by reading their manual first.
  5. Go to a home electronics store and purchase a Y adapter cable of the proper length.
  6. Raise the surround channel speakers.

You can't unless you have a set of speakers to go with it. Examine how your speakers connect. The rear of pc is labeled the same way as the audio receiver.

Already answered Not a question Bad question Other. This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. But it can also depend on the size of the room and your own personal tastes.

Connect Xbox One to Your Home Theater or Sound System

Most surround sound systems have ports for each speaker that you simply plug the appropriate connector into. Is a home theater sound bar as good as a receiver and multiple speakers? Some older systems have clips that you plug bare speaker wire into. You would need a sub with a built in amp.

The realtek manager does not decode any surround. Place the subwoofer near the center of the home theater. Cookies make wikiHow better. The theater sound bars sound great. Verify that you have all of the cables that you need.

You should hear the sound of your computer playing through your stereo. Or do you have analog outputs lime green you do have black and orange? Article Info This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. Current visitors New profile posts Search profile posts Billboard Trophies. Place the surround channel speakers to the side of the viewing area.

How to Connect Surround Sound to a Computer

It Still Works
How to Connect Surround Sound to a Computer

Angle the front speakers towards the audience. Make sure that you have an audio receiver. The center channel bridges the gap between the left and right speaker.

How to Set Up a Surround Sound Speaker System - dummies

Connect the speakers to each other. The subwoofer is omnidirectional sound, which means you will achieve similar results no matter where the subwoofer is placed. Although subwoofers are omnidirectional, placing them against walls and corners will amplify the bass, making it difficult to control. Subwoofers almost always plug directly into the audio receiver.

Home Theater For Dummies 3rd Edition

Make sure to leave some slack at each end to keep the connection from becoming stressed. You can purchase them online. It helps when sound pans from left to right, is dexter still and keeps dialog synced with moving mouths on the screen. Include your email address to get a message when this question is answered. Many people like to place it towards the front of the configuration so that it is easily connected to the receiver.

Surround sound hook up

It Still Works

Each surround sound system will have a slightly different set of instructions detailing the best way to set it up. These go into your stereo. Plug the computer end of the cable into the headphone jack on your computer. Your receiver may also need plenty of room to vent heat, so don't lock it in a cabinet.

How to hook up a surround sound to a desktop computer

How to hook up a 5.1 surround sound to a desktop computer
How to Set Up a Surround Sound Speaker System

On this page

Warnings Be extremely careful not to attach bare speaker wire to a plugged-in item, as doing so may result in a short or an electrical shock. These are used for basic audio. Online is usually cheaper. Run wire from each speaker to the receiver. Arrange the speakers and their wires before connecting anything.

Just so I understand what your attempting? You can't have two audio outputs running at the same time. Determine the length of cable you need. Optical audio is the newest and clearest type of audio, and most modern receivers support it.

  • Be sure to match red to red and white to white.
  • Examine your available speakers.
  • Most surround sound kits include a receiver.
  • Each speaker should be angled in slightly so that it points directly toward the center of the seating area.
  • Each of your speakers should be connected in a line around your room from one front speaker all the way around to the other front speaker.

Tom s Guide Forum

Test out your surround sound. Is this article up to date? This will continue until you shut off the source or until you shut off the receiver.

How to connect your Xbox One to your home theater system for live TV

If you bought your surround sound set second-hand, you may have to buy the receiver separately. Laptop General Discussion. Connect one end of your speaker wire to the back of a speaker, then connect that speaker to another speaker in sequence. At one end the cable will have a plug to go into the headphone jack of your computer. Previous Next Sort by votes.

Measure the distance between the back of your computer to the back of your stereo. Make sure there is a free set of inputs on the back of your stereo. If you can, run the wires under the carpet or through the wall. Question Audio from usb hard drive to surround sound.

Question Getting surround sound from my streaming tv using my receiver, not working. Whichever audio output is operating at the time will cut the audio output on the other. Bobby, can you tell me what motherboard you are using? Plug your receiver into a power source.

Sound - from desktop to tv- surround sound. The back channel speakers should be the same height as the surround speakers. Unlike powered speakers, the average surround sound speaker can't project audio on its own. Also the sub would need to have a speaker output that can run to a set of speakers or a sound bar with a built in amp that have an input the same as the output as the sub. Hooking up soundbar, tv, surround sound rear speakers.

Place the back channel speakers behind the viewing area. Select the input to which you connected the Y adapter. Exclude your subwoofer from this process unless otherwise directed by the manual. If you don't have the proper cables, you can find them online or in tech department stores.

How to Hook up Surround Sound (with Pictures) - wikiHow

Connect Surround Sound
  • Dating in melbourne australia
  • Best london dating sites
  • Dating your brother's ex
  • Free uk chinese dating sites
  • Speed dating findlay ohio
  • Charlotte dating site
  • Dating app zoosk
  • Asian dating site online
  • Taiwanese dating customs